How to Attach a Bolt Snap to Dive Equipment

by Dillon Waters

Bolt snaps are used in a variety of ways with technical gear configurations, and attaching one to their scuba gear is something most divers will need to do at some time or another. Whether you just purchased a new regulator set that needs a bolt snap on the primary regulator and SPG or you are replacing an old clip on a dive light, you need to know how to attach the new snap correctly.

When attaching a bolt snap to your scuba gear, you will want to ensure the connection is strong enough to avoid accidental breakage if snagged, yet it should be something that you can cut or easily remove in an entanglement. It is because of these stipulations most choose to attach bolt snaps to their equipment using braided nylon line. Nylon line is readily available, cheap to replace, durable enough to withstand a great deal of abuse, and it can be easily cut if required.

Below is a step by step guide of how to tie a bolt snap to your gear using nylon line.

What will you need?

  1. 2ft of Braided Nylon (Cave) Line
  2. Bolt Snap
  3. Item Being Attached
  4. Shears
  5. Lighter

It is important to remember to tie the bolt snap tightly to reduce the movement of the clip on whatever you are attaching it to. When attaching a snap to a hose, you can tighten up the knot enough so that the snap will “stand up”, making it easier to grab and clip onto your D-ring.

How to securely attach the bolt snap.

To begin, you will wrap the nylon line around the hose and through the eye of the bolt snap three times as shown below.

Then, you need to tighten up the line to allow the desired distance between the bolt snap and the object.

Next, tie an overhand knot so that it rests against the bolt snap. Pull the knot tightly to secure it and pass the two ends of the line backwards between the bolt snap and the hose.

Now turn over the entire assembly so that you’re looking at the other side. Tie an overhand knot tight enough to snug up the lines running between the bolt snap and the hose. Then, tie a second overhand knot, reverse of the previous one, to make a square knot. Pull the knot very tight.

To complete the knot, trim each end of the line, leaving about 0.25 in free. Burn the ends of the excess line and use the bottom of the lighter to flatten or mushroom the top of burned ends. This helps to avoid the line getting pulled through the knot. Another alternative would be to place a drop of super glue directly on the knot to keep it secure.

Now that the knot is complete, we must examine and test it. Twist it, pull on it, and look for any signs of weakness. You do not want bolt snaps falling off of essential gear, so if it looks questionable, cut the knot and start over.

With the variety of uses for bolt snaps in the diving world, sooner or later most divers will need to attach one to a piece of their scuba gear. Taking the information from this article into consideration while doing so will help ensure a successful and long-lasting attachment of your bolt snap anywhere you need to put it!

Related Blog Articles

12 replies
  1. Jack MacLachlan
    Jack MacLachlan says:

    This is good method for attaching a bolt snap. I would suggest an improvement which ensures that the first knot is balanced and not crossed. Threading the cord means that you start with the cord on either side of the hose and bolt snap. Suggest that you first take the cord and put the two end together to create a loop. Use the loop to attach the cord to the bolt snap. The two loose ends can then be wrapped around the hose…each end twice, so four loops in total. As this is an even number of loops the initial knot will be tied in a balanced way…complete as described above…cheers….Jack

    Reply
  2. Nicolas
    Nicolas says:

    What about cable ties?

    Takes 2 seconds…

    Of the appropriate width, it’s strong enough and can be broken by twisting the eye of the bolt snap

    Reply
    • Dillon
      Dillon says:

      Using a cable tie is a very common practice but they do have the risk of being accidentally broken. This could result in a dangling SPG or regulator, or even a lost dive accessory. The connection should be strong enough that it is only broken when you decide it needs to be.

      Reply
    • Gregory
      Gregory says:

      The problem with cable ties is that you never know when it opens or breaks. It’s not a question of “if” – it’s always “when”. Usually it doesn’t take long – depending on temperature and load applied to it.

      Reply
  3. ZipTyer
    ZipTyer says:

    Guys, cable ties are available in UV resistant……and can be rated to 1200 lbs. So the “They break under heavy loads” is BS. Go get yourself some zip cuffs and let your friend handcuff you and break out of them for me. It can’t be done. That’s why cops use them.
    I’ve used zip ties since forever. They’re cheap enough that I can replace them every year.

    Reply
    • Eric
      Eric says:

      Hey zip tyer, I had an advanced golfer ask me once why I was lining up my putt the way I was. I have him my reason. He then.asks, “do you ever see anyone on the pro circuit do it that way?” No I replied. He then replies” don’t do it that way then”…I’ll give you 1 and only 1 reason why tour formula uv resistant ties are not a good reason. Your in a wreck something catches, you pull your dive knife and go to cut the accessory held by this thick strong plastic. You start sawing and and sawing and sawing. If your lucky tour blade.is serrates, if not your f-d. With nylon, two.swipes.of your knife and your free. A zip won’t do that.

      Reply
  4. Justin Kantor
    Justin Kantor says:

    I use zip ties for may things, but if they are used for dive gear melt and round the ends which may be sharp and can also provide a locking spot if the zip tie slips it will stop on the melted part. An even better knot for this is called a “nail knot” which is easy once you get the hang of it and very secure. It even looks good, and of course we want to look good when we dive.

    Reply
  5. Braden
    Braden says:

    also, on a recent dive I had a small zip tie that held the SPG to a clip just snap off. over time these become brittle and could break at at the wrong time.

    Reply

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

*